Fuel Dispenser System Installation

CommTank is a fuel dispenser installation contractor that serves Massachusetts and New Hampshire fleet, automotive, aircraft and marine customers. We install electronic and mechanical gasoline dispensing systems including Wayne and Gasboy dispensers, control consoles, interconnecting devices and accessories as required for a complete and operating system. Our service trucks also make repairs to existing fuel dispensers and pumps. We are a certified installer for Wayne, Gilbarco, Gasboy, Veeder Root, Red Jacket and OPW products. Our experienced technicians are available for 24 hour emergency response to limit your down time. We are licensed and insured and stand behind our services with a 2 year warranty.

We install dispensers that are compatible with these fuel types:

  • Gasoline
  • Diesel
  • Biodiesel (blends up to 20%)
  • Kerosene (AvGas and jet fuel)
  • E85 Ethanol

CommTank’s technicians utilize the latest technologies to provide professional installations, testing, and repair. We offer a complete fuel system installation service that features underground tanks, double-wall product piping, sumps, submersible turbine fuel pumps and gasoline dispensers. We can provide tank monitoring/inventory control/release detection (Automatic Tank Gauge– ATG) systems including consoles with alarm capability, automatic tank gauging equipment, electronic line leak detectors for primary piping, sensors for all secondary containment (including tank, piping and dispenser sumps), and overfill alarms.

Excavation, trenching, and backfilling required for installation of the fuel system is all part of the job for us. We will determine if unusual conditions or circumstances exist at your site (or in the vicinity of the installation) which could damage the electronic components or circuitry, or otherwise impair the proper function of the system. In such an event, we will install the necessary protective devices into the installation.

Every fuel dispenser installation project complies with the following codes and standards:

  • NFPA No. 30, Flammable and Combustible Liquids Code.
  • NFPA No. 30A, Automotive and Marine Service Station Code.
  • NFPA No. 70, National Electrical Code
  • NFPA No. 329, Handling Underground Release of Flammable and Combustible Liquids
  • EPA 40 CFR Part 280, Technical Standards and Corrective Action Requirements for Architects and Operators of Underground Storage.
  • OSHA 29 CFR Part 1910.106, Flammable and Combustible Liquids.
  • ASTM D2310-80, Standard Classification for Machine-Made Reinforced Thermosetting-Resin Pipe.
  • ASTM D2517-81, Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings.
  • ASTM D2996-88, Standard Specification for Filament-Wound "Fiberglass" (Glass Fiber-Reinforced Thermosetting Resin) Pipe.
  • ASTM D4021-86, Standard Specification for Glass-Fiber-Reinforced Polyester Underground Petroleum Storage Tanks.
  • UL 79, Power-Operated Pumps for Petroleum Product Dispensing Systems. 
  • UL 87, Power-Operated Dispensing Devices for Petroleum Products.
  • UL 567, Pipe Connections for Flammable and Combustible Liquids and LPGas. 
  • UL 842, Valves for Flammable Fluids. 
  • UL 860, Pipe Unions for Flammable and Combustible Fluids and Fire Protection Service.
  • UL 1238, Control Equipment for Use with Flammable Liquid Dispensing Devices. 
  • UL 1316, Glass-Fiber-Reinforced Plastic Underground Storage Tanks for Petroleum Products.
  • API 1615 (1996) Installation of Underground Petroleum Storage Systems.
  • API 1628 (1996) A Guide to the Assessment and Remediation of Underground Petroleum Releases (if a release is expected).
  • California Air Resources Board (CARB) Executive Orders applicable to system.
  • California Air Resources Board (CARB) Test Procedures applicable to system.
  • PEI RP 100-05 Recommended Practices for Installation of Underground Storage Systems. 
  • PEI RP 300-04 Recommended Practices for Installation and Testing of Vapor Recovery Systems at Vehicle Fueling Sites. 
  • PEI 400-02 Recommended Procedures for Testing Electrical Continuity of Fuel-Dispensing.
  • All other applicable ASTM and UL standards.
  • All applicable EPA requirements relating to release detection, spill and overfill prevention, and corrosion protection.
  • All other applicable Local, County, State, and Federal codes, standards, licensing and registration requirements.

Our goal is to provide quality fuel dispenser installations in the most cost effective manner possible. A fuel dispensing system must be successfully tested, certified, registered, and have all necessary permits to conduct dispensing of gasoline. We generate AutoCAD drawings of your site and provide the most efficient layout for your space. Fuel Island Canopies and Valances can be constructed by our crews to protect your personnel and customers. Facility owners no longer need to coordinate separate contractors when you select CommTank as your fuel dispenser service company.

For examples of our work please see the fuel dispenser installation projects section of our web site.

 

Contact CommTank today for expert fuel dispenser and gas pump services in Massachusetts and New Hampshire: 1-800-628-8260